1 data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s speci? cations are subject to change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers before ordering. 2. this datasheet has only typical speci? cations because there is no space for detailed speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. http://www.murata.com/ 1 noise suppression products/emi suppression filters > common mode choke coil > wire wound type for large current 2012.7.5 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. common mode choke coil wire wound type for large current dlw5ah/dlw5bs series (2014/2020 size) c dimensions dlw5ah series (l) 5.00.3 (t) 4.3 max. (w) 3.60.3 0.5 min. 0.45 min. 1.7 0.3 (2) (1) (4) (3) 1.7 0.3 1.3 0.3 1.3 0.3 1.3 0.3 0.9 0.3 starting position of wiring should be covered with resin. * * * (in mm) : electrode c dimensions dlw5bs series (l) 5.00.3 (t) 4.5 max. 3.60.3 (w) 5.00.3 0.5 min. 0.45 min. 1.70.3 (2) (1) (4) (3) 1.70.3 1.30.3 1.30.3 0.90.3 3.00.5 1.30.3 (in mm) : electrode : marking (top) (bottom) 0.50.3 c impedance-frequency characteristics (main items) impedance ( ) frequency (mhz) 100000 10000 1000 100 10 1 10 100 1000 dlw5ahn402sq2 dlw5bsm302sq2 dlw5bsm152sq2 dlw5bsm102sq2 dlw5bsm351sq2 dlw5bsm191sq2 common mode dlw5ahn402sq2 dlw5bsm302sq2 dlw5bsm152sq2 dlw5bsm102sq2 dlw5bsm351sq2 dlw5bsm191sq2 differential mode c equivalent circuit (1) (4) (2) (3) no polarity. c packaging code packaging minimum quantity l 180mm embossed tape 400 k 330mm embossed tape 1500 b bulk(bag) 100 c rated value ( p : packaging code) part number common mode impedance (at 100mhz/20c) rated current rated voltage insulation resistance (min.) withstand voltage dc resistance operating temperature range dlw5ahn402sq2 p 4000ohm (typ.) 200ma 50vdc 10m ohm 125vdc 3.0ohm max. -25 to +85c dlw5bsm191sq2 p 190ohm (typ.) 5000ma 50vdc 10m ohm 125vdc 0.02ohm max. -40 to +85c dlw5bsm351sq2 p 350ohm (typ.) 2000ma 50vdc 10m ohm 125vdc 0.04ohm max. -40 to +85c dlw5bsm102sq2 p 1000ohm (typ.) 1500ma 50vdc 10m ohm 125vdc 0.06ohm max. -40 to +85c dlw5bsm152sq2 p 1500ohm (typ.) 1000ma 50vdc 10m ohm 125vdc 0.1ohm max. -40 to +85c dlw5bsm302sq2 p 3000ohm (typ.) 500ma 50vdc 10m ohm 125vdc 0.3ohm max. -40 to +85c number of circuit: 1 continued on the following page.
2 data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s speci? cations are subject to change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers before ordering. 2. this datasheet has only typical speci? cations because there is no space for detailed speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. http://www.murata.com/ 2 noise suppression products/emi suppression filters > common mode choke coil > wire wound type for large current 2012.7.5 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. continued from the preceding page. c derating of rated current derating of rated current in operating temperature exceeding +75c, derating of current is necessary for dlw5bsm191sq2 series. please apply the derating curve shown in chart according to the operating temperature. operating temperature (c) rated current (a) 4.5 4.75 5 0 1020304050607080 75c 85c 90 100 dlw5bsm191sq2 c ! caution/notice ! caution (rating) do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. notice solderability of tin plating termination chip might be deteriorated when low temperature soldering pro? le where peak solder temperature is below the tin melting point is used. please con? rm the solderability of tin plating termination chip before use.
|
